How to Clean a Bissell Vacuum Filter?

Vacuum cleaners are a great helper for your house cleaning. But when this cleaning machine gets dirty, it can make your whole house dirty since you will not be able to clean the house without this machine. So for that, keep up your vacuum is more critical.

We know that everyone loves a Bissell vacuum. So for that, we are here with this guide telling how to clean the Bissell vacuum filter.

How to Clean Upright and Canister Vacuums?

Step 1: Disconnect Vacuum Cleaner

While emptying the vacuum, unplug it. Ensure that the electricity is turned off. Then, remove the vacuum cleaner from the socket.

Cleansing and maintaining the vacuum even when it is attached to a source of electricity may cause electrocution.

Step 2: Clean the Exterior

If the exterior of the vacuum is unclean, you can wipe it off with a clean towel, also under the canister.

Step 3: Empty the Dust Tank

Every vacuum cleaner comes with a marking indicating that the tank needs a clean-up. When the marking turns on, you must remove the dust tank, rinse, and dry it with a dry cloth. Then, when you put it back into the vacuum, make sure it snaps in place.

Some of the vacuum models might come with a releasing latch that can let the dust container out. If you want to know about your vacuum’s dirt tank removal method, check out your model’s user guide here.

Step 4: Cleaning Brush Roll

Now remove the brush roll and clear off all the wrapped fur and dirt. First, Ou must thoroughly pull all the dirt and debris from the brush roll. The side of the brush roll must not have any strings or hairs. After that, clear the passageway as well while changing the brush.

Depending on your vacuum model, you might have a release button or screws. The release button becomes easy to clean, while the screw might need a Philips head or flathead screwdriver. If you are cleaning the brush frequently, it will keep the vacuum working for a long time.

Step 5: Clean the Filters

The most crucial part of vacuum cleaning is to clean the filters. You must wash the filters regularly or unless it indicates to do so. For that, you can run the filters through the warm water. While washing, you can employ a tiny amount of washing liquid. Mildly brush the filter. Now rinse the water through filters carefully. Let the filter air dry because a wet filter will lead to disaster when you plug it in.

How to Clean Bagless Vacuum Filters

If your vacuum is a bagless model, then it will have three filters. All of them are washable. Instead of needing to extract and discard a vacuum bag filled with dust and other debris, you can dump the dirt bin of this vacuum model. Clear the vacuum’s filtration at least once per month, perhaps as necessary, to keep it running smoothly. Only utilize the filters labeled “Style 10” if you want to change any of the filters.

Inner and Outer Circular Filter Cleaning

• To unlock and dislodge the filter cup at the lower part of the bucket, turn it anticlockwise. Then, to extract the round filters, turn them counterclockwise and lift them upward or free of the container.
• Disconnect the outer cover and internal pleat filters before hand-washing these in the heated water one by one time. If they’re highly filthy, one may add a few drops of light dish-washing soap to the water. Then, before placing the filters back into the filtration system cup, thoroughly wash them with water, put them on a water-absorbing cloth, and let them dry naturally.
• When you wash the filters, go for washing the filter up in warm soapy water. After washing and rinsing, let the cup air dry. Besides, you can clean the upper container and louvers with a damp towel also.

Premotor Filter Cleaning

The pre-motor filter is positioned beneath the vacuum’s dirt canister and filter cup and in the Lock ‘n Seal mechanism center. It shields the appliance’s machine against dust, debris, as well as other things. Extract the tiny filter from the vacuum, clean it of all significant, granular materials, and wash it under heated water afterward. When reinstalling the filter, allow it to air dry thoroughly.

Post-Motor Filter Cleaning

The post-motor filter is located at the back of the opening on the front of the vacuum. It aids in the transfer of clean, dust-free airflow into the chamber throughout the cleaning procedure. First, remove the filter from the cleaner and clean it manually within warm water. Then, once more, you can put a few drops of a mellow dish-washing detergent into the water to wash a clogged filter.

Wash down the filter with warm water and let it air-dry utterly before replacing it. To change the door, put the tabs on the opposite side of the opening. Then press the other side into place.

Step 6: Clean the Inner Cyclone (Optional)

1. The interior Cyclone of some versions, namely the Cleanview OnePass 9595 and Revolution 12901, could be detached and cleaned as well. Turn the Cyclone clockwise to release it. Take out of the container by pulling it down. Wipe it with a damp towel and leave it to dry in advance of replacing it.
2. Lift the lid to the pre-motor filtration system to substitute the Cyclone when it’s dry. Put the Cyclone in the tank’s upper slots. Rotate the Cyclone counterclockwise to secure it in position.

Bottom Line

If your Bissell vacuum’s surface becomes filthy, clean it up with only a dry towel. Clear the dust container and clean or replace the filtration bags regularly to keep your cleaner in good working order. You can clean filters on some versions that can be manual. Some feature filters that should be shaken off rather than washed and must be changed more often. It’s critical to keep the brushes on your vac clean of contaminants such as fur and thread. When servicing your vacuum,  verify it’s switched off and disconnected from any source of power.