5 How to Put a Belt on a Bissell Vacuum Hacks you need to know
If your Bissell vacuum’s brush roll isn’t spinning, it might be due to a broken brush roll or it becoming detached from the motor spindle. If you’re not sure how to fix it, you’re in the right place for assistance. After you have replaced the drive belt, you need to hook one end onto the motor pulley and stretch the other end over the rotating floor brush, situated amidst the bristles. Ensure the ends of the brush are secured in the designed slots, and then give the brush a few turns to check if the belt is properly aligned.
Look for signs of wear and tear on the brush or belt if you detect a change in vacuum performance or noise. Recline the vacuum handle and turn the vacuum upside down after disconnecting it. Remove the six screws with a Phillips head screwdriver and raise the brush plate. To remove the revolving floor brush from the vacuum, grasp both ends and lift it straight out of the machine.
Remove the debris from the brush and drive belt . Snip the hair or string that is wrapped around it using scissors. Taking the belt off the motor pulley will allow you to inspect it for signs of wear or damage. Your belt should be replaced if you notice any signs of wear or tear. To find replacement belts for your BISSELL appliance, visit BISSELL.com.
Once you’ve replaced the drive belt, you should place one end over the motor pulley and the other end over the revolving floor brush in that area between the bristles. Make sure that the belt is centred by putting the ends of the floor brush into the slots and rotating the brush several times. Screw the six screws into the brush plate after repositioning it.
What You’ll Be Able to Accomplish
Vacuum owners should know how to change a vacuum belt at home to save time and money, which is a simple fix. Everyone can save money and effort by learning the basics of vacuum belt replacement.
Vacuum belt replacement is a very straightforward repair on most vacuums. There should be no need to take a vacuum cleaner to a repair shop for a belt change. The first step in this (and any) part replacement is to order the correct part.
How to Put a Belt on a Bissell Vacuum Hacks
The steps to replace the belt can vary slightly depending on the model and style of vacuum. As a result of these differences, all vacuum belt replacements are essentially the same. Most vacuums can be fixed in less than five minutes if the owner is familiar with the model.
In the steps below you’ll know in detail how to put a belt on a bissell vacuum.
Step 1:Get into the Vacuum’s Belt and Brush Roll Area to Clean
Vacuum belts spin the brush roller and the vacuum’s wheels on some self-propelled models. The brush roll area of any vacuum is where this repair will take place. For most vacuum cleaners, opening the brush roll area is as simple as removing the bottom plate. The bottom plate can be removed by unscrewing four Phillips screws on our demonstration model.
Step 2:Remove the Brush roller and the Old Belt from the Machine
After removing the bottom plate, now remove the vacuum’s old (or broken) belt. Check the vacuum’s internal arrangement and connections before removing the old belt and brush roll. The first step is to remove the vacuum brush roll from the belt loop. To remove the opposite end of the vacuum belt, disconnect it from the motor’s shaft.
Step 3: Attach the New Vacuum Belt to the Motor Shaft and Brush Rollers Using the Original Belt
There’s a problem here! Belts are held between the motor shaft and brush roller using tension in vacuum models that use round or flat belts. There is a chance that the replacement belt won’t fit in the vacuum.
If this sounds familiar, it’s probably typical. Make sure you have the correct part for your vacuum, but be aware that round and flat vacuum belt types stretch a lot with time. Geared and v-belts, on the other hand, don’t stretch nearly as much.
Vacuum usage has stretched out the old belt, making it look considerably larger than the new belt compared to its original size. In order to install a new vacuum belt, first, wrap the old one around the suction motor. As soon as the brush roll is attached to the shaft, you may begin spooling it through the belt.
Step 4: Attach the Brush Roller and Ensure the Belt Is Properly Centred
Regardless of the vacuum’s design, the brush roll and belt must be returned to their original locations before the vacuum may be closed. In order to get the brush roll into place with that new, upstretched belt on it, you’ll need a little brute force.
In our demonstration vacuum, the brush roll on the other side of the belt is fitted with a notch that allows it to be pulled through the vacuum. Just tug on it hard enough, and it’ll snap perfectly into place, no muss, no fuss, no muss (watch your fingers). Standing over the vacuum while it is on the ground makes this much simpler. The correct counterbalance can be provided by a well-placed foot.
Step 5: Put the Vacuum Back Together
The brush roll region can be accessed by reinstalling the vacuum’s bottom plate and any other housing elements removed. The wind tunnel’s four Phillips screws and bottom plate may be returned.
The repair has been completed. Depending on the type of vacuum belt you use, you may not need to replace your vacuum agitator belt for months or even years.
Final Words
Finally, you’ve got the answer you were looking for! Your Bissell vacuum cleaner has received a new drive belt. As you can see, replacing the drive belt on your vacuum is quite simple, and we hope that our instructions have been of use to you. After unplugging and flipping it over, we’ll need to remove the sole plate by unscrewing these four screws. This is the brush roll with the belt wrapped around it after you remove the sole plate.
